6G v2.0

[tobyw]

Thats so cool, when I clicked i figured it was a ratchet strap around the tire kind of affair

Nope... that's what the water jug is held on with though

IMG_7270.JPG (1.3 MiB) Viewed 4934 times

[tobyw]

I don't know why, but I just cannot shake the boy-racer side of me that has a soft spot for LED light bars I would actually really like to go with something more like the KC Gravity Pro-6 setup with it's round lights that seem a little more fitting with the softer lines of the 6G, but both VISA and Mastercard have suspended my sponsorships so I am relegated to the likes of Amazon special edition units... At any rate, I spent a little time fab'ing up some simple brackets and hung a 50" curved unit over the weekend:

IMG_7933.JPG (1.12 MiB) Viewed 3273 times

IMG_7935.JPG (992.46 KiB) Viewed 3273 times

IMG_7938.JPG (1.51 MiB) Viewed 3273 times

IMG_7939.JPG (1.11 MiB) Viewed 3273 times

IMG_7951.JPG (1.85 MiB) Viewed 3273 times

[tobyw]

Well... in a very disheartening turn of events, the LED light bar is no more After several attempts to mitigate the wind noise, I just could not live with it for a daily driver and it had to come back off:

IMG_7989.JPG (1.23 MiB) Viewed 3258 times

On the other end of things, literally, I spent a few minutes combing the online catalogs found a replacement swing gate cylinder that would prevent the gate from opening beyond 90*, avoiding the collision of my Rotopax with my taillight housing when I have it strapped to the spare tire:

IMG_7995.JPG (1.61 MiB) Viewed 3258 times

IMG_7996.JPG (1.43 MiB) Viewed 3258 times

IMG_7997.JPG (1.61 MiB) Viewed 3258 times

IMG_8001.JPG (1.66 MiB) Viewed 3258 times

[tobyw]

Finally took the time to install a permanent brake controller... As I've mentioned before, I really like the wireless brake control setup as it works flawlessly and is brick simple to move between vehicles, but the trailer mounted control module is not handy for multiple trailers. Since the Donkey sees duty towing our camp trailer, flatbed, and dump trailer from time to time, having a dedicated brake controller just makes life easier. And I'm lazy, so I'm all about making life easier

IMG_8521.JPG (1.62 MiB) Viewed 3238 times

IMG_8523.JPG (1.27 MiB) Viewed 3238 times

IMG_8525.JPG (1.52 MiB) Viewed 3238 times

IMG_8529.JPG (1.3 MiB) Viewed 3238 times

IMG_8532.JPG (1.35 MiB) Viewed 3238 times

[tobyw]

After nearly a year since the last update, which has included countless wheeling trips and miles traveled off-road "BDR-style" towing the little camp trailer around, I finally got around to taking another crack at an LED light bar. Sort of... Version 1.0 was a terrific failure because of the unbelievable wind buffeting it caused with the soft top. I always had a hunch that something more like the KC Gravity Pro-6 light bar might work better by allowing some air to travel around and through the profile, but I wasn't about to drop $1,800 on an experiment like that. Plus, due to my drive-by-braille driving antics, having something that expensive be so exposed simply didn't seem like the right answer

Enter Amazon and their ever-present flash sales... I scored a grip of 4-1/4" round LED light pods for a song, and with the Prime membership benefit of free returns there was really no risk other than my time. I spent a few minutes tinkering with a new tube roller, which for the record is cool as heck, and glued on some tabs to mount the lights themselves. Believe it or not, I had to foresight to actually save the mounting brackets I had fab'd up for the original 50" LED bar last fall, and grafted them into the design of the new setup. Once the smoke cleared out, I stood back to see what happened:

IMG_0787.JPG (1.47 MiB) Viewed 390 times

IMG_0788.JPG (1.59 MiB) Viewed 390 times

IMG_0789.JPG (1.76 MiB) Viewed 390 times

IMG_0801.JPG (1.3 MiB) Viewed 390 times

IMG_0803.JPG (1.36 MiB) Viewed 390 times

I am happy to report that it makes no appreciable difference in wind noise at speed Having just racked up nearly 1,000 miles through the Idaho BDR and not even noticing it up there except when it was switched on, I'm going to chalk this one up as a win

IMG_0989.JPG (2.06 MiB) Viewed 390 times

[tobyw]

My disdain for having to constantly deal with straps to restrain my storage bins combined with my ever-present ADD led me down the rabbit hole of alternate storage solutions. Dryside showed me the light with the Milwaukee Packout system that he has incorporated into his JKU-R build, and it combines two of my favorite things: LEGOS and Tetris. I leaned into the system hard and picked up a variety of bins, boxes, and one soft-sided bag that may well be my favorite piece of the entire outfit. I used a large base plate for the lower deck, and modified my patented Harbor Freight upper deck storage rack to accommodate one of the smaller base plates:

IMG_1179.JPG (1.65 MiB) Viewed 317 times

IMG_1181.JPG (1.64 MiB) Viewed 317 times

IMG_1182.JPG (1.57 MiB) Viewed 317 times

IMG_1200.JPG (1.62 MiB) Viewed 317 times

IMG_1204.JPG (1.37 MiB) Viewed 317 times

IMG_1203.JPG (1.36 MiB) Viewed 317 times

With that handled, it was time to address, uhhhhh, handles Another big miss on the 6G platform is A-pillar grab handles. I complained about it on 6G v1.0, and ended up fabricating two different versions of a grab handle to make my life just a little better. Why it took me nearly two-years to get there with the Donkey I cannot explain, but I'm very happy I finally got off the couch and did it. The process to get these fabricated and installed is gory, and it involves cutting platstic trim pieces and generally making irreversible changes to the interior bits, but the end result is totally worth it:

IMG_1215.JPG (1.19 MiB) Viewed 317 times

IMG_1225.JPG (1.99 MiB) Viewed 317 times

IMG_1223.JPG (1.41 MiB) Viewed 317 times

IMG_1226.JPG (1.34 MiB) Viewed 317 times

IMG_1230.JPG (1.25 MiB) Viewed 317 times

IMG_1231.JPG (1.36 MiB) Viewed 317 times

[tobyw]

One of my other big gripes about the Bronco centers around the Sasquatch package wheels. I had already taken care of making them as visually appealing as I could by shooting the decorative trim ring a silver color, but the aforementioned trim ring was really the problem regardless of what color it was... You see, although it admittedly offered unparalleled protection for the valve stem, that protection came at the cost of access to the valve stem. My fat fingers simply could not reach in behind the trim ring to manipulate the valve stem cap, particularly when it was wet and/or cold. Plus, after nearly two years of constant abuse, they were just looking a little rough around the edges, literally:

IMG_7636.JPG (1.01 MiB) Viewed 78 times

IMG_7637.JPG (984.08 KiB) Viewed 78 times

IMG_7638.JPG (1.13 MiB) Viewed 78 times

To finally fix the situation, I ordered up a new set of wheels and had them mounted up on the battle tested 37" BFG's:

IMG_1255.JPG (1.52 MiB) Viewed 78 times

IMG_1256.JPG (1.43 MiB) Viewed 78 times

IMG_1258.JPG (1.48 MiB) Viewed 78 times

The wheels are 17x9 KMC GRS549's with -12mm offset. These are actually the same style of wheel I'm running on the LJ, and I really like the way they contrast the otherwise black-n-blue theme on the Donkey:

IMG_1259.JPG (2.03 MiB) Viewed 78 times