jeeps been in the family for a while... just basically been a stock 4.2/ax15 with d30/35 axles 4inc lift and 33's
now has a dana 60front,reid knuckels, high steer, 35spline, clean all thats left is hubs, and front locker
rear is dana 60 disk conversion, with tru track,
rollin on some 17's with 36's irocks plan on going mtrk's
got rid of the nasty 4.2/ax15/231
for a 4.6fi stroker,new jacobs ax15/terralow 231 with short sye, 4:1
just keepin it easy,
how it sets in my shop.
this is my first inline6 swap, ive done tbi and tpi, and ls1 but never this
so help is needed,
i got the harness all in and so far working, the engine harness i guess is out of a newer wrangler (93 i think), i have power but the starter dont work, and i dont have power to the fuel pump,
i just picked up a e2000 inline fuel pump from a ford to do the swap, so i dont have to deal with the intank crap,
and i have this plug under the dash i dont know where it goes..
i think i might have to switch out the harness under the dash to get everything elce to work..
YJ 1ton build. 4.2-4.6 stroker fi swap
-
- Posts: 421
- Joined: Wed Sep 17, 2008 8:56 am
YJ 1ton build. 4.2-4.6 stroker fi swap
Camaro turbo lsx th400
06 Cummins "racetruck"
tj 1ton 40's 5.3 build
509 Crawlers on the facebook
06 Cummins "racetruck"
tj 1ton 40's 5.3 build
509 Crawlers on the facebook
-
- Posts: 421
- Joined: Wed Sep 17, 2008 8:56 am
-
- Posts: 421
- Joined: Wed Sep 17, 2008 8:56 am
Got the jeep runnin and all together.. the 94yj to 89yj swap was kinda cool.. only needed to one one wire for the ign switch. And one wire to power for the fuel pump..
I ran a e2000 pump inline with a gm fuel filter. And it work ok. Think i might need to add a helper pump later. But the motor runs and sounds good. Pretty quiet.
The 87 harness already had the fuel pump wiring just needed to add power. It was nice..
Now some gauges dont work due to the 94 to 97 harness.. so custom gauges it is.
Now all thats needed.. front d60 hubs. Brakes.. install front drive line. Lift rear. Heater core Gauges..
Now to the brakes.. the yj mc is not enough to lock up the dual piston calipers f/r so i am thinkin of the f350 mc i was told its a straight swap. Little grinding. Then some adapters for the lines.... Ill post pics when i get the parts
I ran a e2000 pump inline with a gm fuel filter. And it work ok. Think i might need to add a helper pump later. But the motor runs and sounds good. Pretty quiet.
The 87 harness already had the fuel pump wiring just needed to add power. It was nice..
Now some gauges dont work due to the 94 to 97 harness.. so custom gauges it is.
Now all thats needed.. front d60 hubs. Brakes.. install front drive line. Lift rear. Heater core Gauges..
Now to the brakes.. the yj mc is not enough to lock up the dual piston calipers f/r so i am thinkin of the f350 mc i was told its a straight swap. Little grinding. Then some adapters for the lines.... Ill post pics when i get the parts
Camaro turbo lsx th400
06 Cummins "racetruck"
tj 1ton 40's 5.3 build
509 Crawlers on the facebook
06 Cummins "racetruck"
tj 1ton 40's 5.3 build
509 Crawlers on the facebook
Return to “Projects and Build-Ups”
Who is online
Users browsing this forum: No registered users and 51 guests