pickup project

Post pics and info of your current projects.
79chevy39.5's
Posts: 1204
Joined: Wed Apr 11, 2007 7:48 pm

pickup project

Postby 79chevy39.5's » Mon Mar 11, 2013 9:40 pm

recently i sold my 2001 2wd 24valve dodge 2500 it was 2wd and i didnt like that much so working a few saturdays got me a 1998 dodge 3500 12valve most importantly 4x
this is how it came to me it had a service box on it prior and the guy wanted to keep it
Image
picked up a bed off cl for $100 and a blown t5 that was given to me its pretty nice shape and good tailgate to boot also installed a 2.5" leveling kit and a set of 37" goodyear milspec takeoffs thank to white trash
Image

79chevy39.5's
Posts: 1204
Joined: Wed Apr 11, 2007 7:48 pm

Postby 79chevy39.5's » Mon Mar 11, 2013 9:42 pm

the bed isnt mounted as i have to do some figuring as the frame wheelbase is longer than std cab long box configuration by about 4" or so not exactly sure on exact length i have a new grille and mirrors on order to get rid of the playgrounds on the side

User avatar
TJDave
Peak Putters VP
Peak Putters VP
Posts: 2806
Joined: Sat Jan 12, 2008 11:47 am
Location: East Richland

Postby TJDave » Tue Mar 12, 2013 4:05 pm

8) cool! You un-dually'd it.
2018 JLU Rubicon
Tow bar mount
Trailer hitch

79chevy39.5's
Posts: 1204
Joined: Wed Apr 11, 2007 7:48 pm

Postby 79chevy39.5's » Tue Mar 12, 2013 6:38 pm

yes i have zero need for a dually and these trucks to have 4.10s is crazy low in my opinion so 2 birds one stone and the h1 take offs cost the least and are load rated at 3200 lbs or so i think

next steps will be seal up some oil leaks (the vaccume pump) front cover and tab kdp while im at it remove the broken bolts in the head from the exhaust manifold (may replace manifold with 3 piece unit) and after that it will be time for mods (new track bar and bracket upgrade the steering as well)

79chevy39.5's
Posts: 1204
Joined: Wed Apr 11, 2007 7:48 pm

Postby 79chevy39.5's » Sun Mar 17, 2013 7:55 pm

spent the day working on the rig again today, pulled turbo and exhaust manifold and drilled out some broken bolts out of the head got all but one out perfectly the last one required some serious m'fin ended got it out and the manifold hasnt shrank too much and lined it back up bolted it back on no more manifold leak and replaced the wastegate fitting out and put a plug in there to shut the wastegate off cleaned out the sediment bowl (pretty dirty in there) still have a steady miss under no load and some white smoke wanting to check the timing anyone on here have the cummins adapter?

got both mirrors cut off have some searious body work to do on the doors to get them welded up and straight pass side looks like it was ripped off before also looking for a front section of a bed to close the gap between the cab

also made some mounts for the front of the bed need to finish up the back mounts and get the hitch back on

79chevy39.5's
Posts: 1204
Joined: Wed Apr 11, 2007 7:48 pm

Postby 79chevy39.5's » Thu Mar 21, 2013 6:45 am

little update photo pulled the truck out of the garage last night and drove it to work this morning hope to put front crank seal in during lunch and after work finish it up new grill as mine had no tabs holding it on any more jsut some bailing wire and the new mirrors are on
Image

79chevy39.5's
Posts: 1204
Joined: Wed Apr 11, 2007 7:48 pm

Postby 79chevy39.5's » Fri Mar 29, 2013 8:36 pm

Just got some more things for the truck a wrecked truck bed to get the front few inches offto fill the gay between cab and box. Front fender to replace creased one
Started to cut out the holes from the old mirrors and some 4 inch pipe to start on a rear bumper oh and my gauges came so I can monitor the vitals

79chevy39.5's
Posts: 1204
Joined: Wed Apr 11, 2007 7:48 pm

Postby 79chevy39.5's » Wed Feb 12, 2014 9:28 pm

Image

Swapped over to ford spindles and hubs well one side do the other tomorrow it adds an inch to wms so tried out my 12 bolt h1s with grooved goodyears (thanks steve and popgun) clears nicely


Return to “Projects and Build-Ups”

Who is online

Users browsing this forum: No registered users and 14 guests