Bunny v2.0

Post pics and info of your current projects.
User avatar
Don
Posts: 816
Joined: Wed Mar 14, 2007 4:40 pm
Location: Pasco, WA

Bunny v2.0

Postby Don » Wed Aug 03, 2016 1:45 pm

The trails have been calling, wheeling season is coming fast, and there's not enough hours in my day to get the CJ to where it needs to be. In all honestly, when the CJ works, it works well, but the reliability issues have been gnawing at me, and frankly kept me off the trails.

I know it's almost blasphemy to infer the name of the somewhat famous (infamous) Bunny on another vehicle, but I hopefully v2.0 will carry a little luck of the Bunny and be just as much fun!

Meet Bunny 2.0
Bunny2.jpg
Bunny2.jpg (88.54 KiB) Viewed 11215 times


It a '93 Explorer Sport, 4.0L, 5 speed, 3.73L 8.8 rear, D35 front. Runs great, shifts good, A/C blows cold, all the windows work, every bushing in the suspension is wasted and the brakes are junk.

The goal here is reliable, streetable, tough and fun. Intended purpose is trails, back country adventures (long distance), mild whoops, occasional sand and maybe a tough truck race or two.

There's the plan:

1 - complete brake/ wheel bearing rebuild, front to back (parts on the way)
2- James Duff 5.5" system, long arms, quad shocks up front, fabbed coil buckets, lift leafs in the rear (parts on the way)
3- Aussie locker up front
4- 33" tires. Looking at the new Grabber MT (not the desert tires)
5- Cage, bumpers, body protection, swap the winch over from the jeep

This should be a solid base to start with. Down the road I'll do things like air compressor, storage, spare tire mount, etc, etc, etc.

Lets start the fun! See you at the 50th Anniversary run!

OldGreen
Posts: 4502
Joined: Tue Mar 13, 2007 6:21 am
Location: coming or going?

Re: Bunny v2.0

Postby OldGreen » Wed Aug 03, 2016 4:55 pm

I love this plan.

Wrench
Peak Putters Member
Peak Putters Member
Posts: 1237
Joined: Sat May 30, 2009 7:23 am
Location: in a van down by the river

Re: Bunny v2.0

Postby Wrench » Wed Aug 03, 2016 5:39 pm

Awesome! :thu2:
Paul
'84 XJ, '19JL

Jay W
Posts: 58
Joined: Sun Nov 18, 2012 1:09 pm
Location: Yakima, WA

Re: Bunny v2.0

Postby Jay W » Wed Aug 03, 2016 8:06 pm


User avatar
Don
Posts: 816
Joined: Wed Mar 14, 2007 4:40 pm
Location: Pasco, WA

Re: Bunny v2.0

Postby Don » Fri Aug 05, 2016 1:22 pm

Does anyone have any opinions on 33x12.50 vs 33x10.50? I'm leaning toward the 10.50, especially if I can get my hands on the new Grabber X3's. The only downside I see on the 10.50's is snow flotation and potentially lower sidehill stability. The 10.50's will keep my overall width down, I can run a factory a factory wheel, should be easier on wheel bearings, will make sure I keep the sweet turning radius of the TTB, should reduce rolling resistance ...

What's your thoughts?

OldGreen
Posts: 4502
Joined: Tue Mar 13, 2007 6:21 am
Location: coming or going?

Re: Bunny v2.0

Postby OldGreen » Fri Aug 05, 2016 1:32 pm

Danny accidentally bought some 33x10.50r15 BFGs. They worked fine and he went everywhere everyone else did. Of course, his Jeep weighs next to nothing and. . .well. . .he's Danny. :D

Honestly, I think they would be fine. You are the engineer but it seems like diameter has more to do with aired down contact patch than width. Comparing 1" to 1" that is.

User avatar
Roman
Peak Putters President
Peak Putters President
Posts: 2743
Joined: Wed Mar 14, 2007 5:30 pm
Location: Kennewick, WA

Re: Bunny v2.0

Postby Roman » Fri Aug 05, 2016 9:47 pm

Don, why the worry about overall width? TTB Fords aren't all that wide to begin with.

User avatar
Lud
Peak Putters Member
Peak Putters Member
Posts: 1042
Joined: Wed Nov 07, 2007 2:50 pm
Location: Pasco, WA

Re: Bunny v2.0

Postby Lud » Fri Aug 05, 2016 9:59 pm

What's the rim width? If it's 15x7 I would go with the 10.5, if its 15x8 I would go with 12.5. That is if you want to air down the tires under 10psi with less chance of losing the bead.
2004 TJ Wrangler X (Rubiclone)
2.5" OME Lift, 1.25 in Body Lift, Flat Fender Flares
35x12.50x15 Maxxis Razor MTs
D30 ARB 4.56s Rear JKD44 w/ 8.8 disk brakes Ford 9" goodies, 4.56 and ARB.

User avatar
Don
Posts: 816
Joined: Wed Mar 14, 2007 4:40 pm
Location: Pasco, WA

Re: Bunny v2.0

Postby Don » Sat Aug 06, 2016 6:39 am

Lud wrote:What's the rim width? If it's 15x7 I would go with the 10.5, if its 15x8 I would go with 12.5. That is if you want to air down the tires under 10psi with less chance of losing the bead.


Your comment just invoked a ptsd like reaction, I have a deep hate for losing beads! If I went 10.50 I'd run stock 15x7`s. I'd have to buy some 15x8`s for 12.50`s. Bead locks may be in the future, just not in the budget right now.

User avatar
Don
Posts: 816
Joined: Wed Mar 14, 2007 4:40 pm
Location: Pasco, WA

Re: Bunny v2.0

Postby Don » Sat Aug 06, 2016 6:43 am

Got my shipping confirmation, 340lbs of James Duff is scheduled to deliver on 8/11!

User avatar
Lurch
Peak Putters Member
Peak Putters Member
Posts: 2363
Joined: Thu Nov 08, 2007 7:10 am
Location: Pasco

Re: Bunny v2.0

Postby Lurch » Sat Aug 06, 2016 7:35 am

I'd go 12.5s. I like the look better and it will add to stability in off camber spots.
You can follow me.... but it's gonna hurt ;)

User avatar
Don
Posts: 816
Joined: Wed Mar 14, 2007 4:40 pm
Location: Pasco, WA

Re: Bunny v2.0

Postby Don » Sat Aug 06, 2016 8:25 am

Here's the laundry list of parts ordered this morning:

Brake rotors, brake pads, calipers, wheel bearings, bearing seals, brake drums, brake shoes, wheel cylinders, brake hardware kits, adjusters, ball joints, ball joint camber eccentrics, master cylinder

... That ought to take care of the brake issues!

I also ordered my front aussie locker and parts for the c clip eliminator.

Aside from the tires, all the big purchases are out of the way. Guess next weekend is going to be a wrench fest!

User avatar
Don
Posts: 816
Joined: Wed Mar 14, 2007 4:40 pm
Location: Pasco, WA

Re: Bunny v2.0

Postby Don » Thu Aug 11, 2016 6:57 pm

KIMG1194-640x360.jpg
KIMG1194-640x360.jpg (54.88 KiB) Viewed 11106 times


Should have left cookies for Brown Santa!

User avatar
Don
Posts: 816
Joined: Wed Mar 14, 2007 4:40 pm
Location: Pasco, WA

Re: Bunny v2.0

Postby Don » Thu Aug 18, 2016 8:35 am

So, after taking two days off last week to clear my plate of house/ yard chores, I've gotten about 10 hours in to the Bunny project. Right now, both axles are off the truck. The front is stripped down to bare beams and ready for cleaning, trussing, painting and the Aussie locker install. The rear has the brakes stripped down. Still need to pull the axles and get it ready to truss.

I've been considering the rear axle truss design a lot. After personally having broke an 8.8 housing on the race truck this is important to me. Image All of the trusses on the market are designed for Jeep axle swaps and do not extend past the SOA perches. I'm leaving the Explorer SUA, so I really want to get that support all the way to the ends of the axle. So, I need to figure out a truss that integrates the bump stops, accommodates the u bolts, and gets as far out as possible on the axle tubes. I'm considering using 1.5" DOM as opposed to plate, to minimize the amount of welding I have to do on the tubes to prevent warpage.

Image

Image

Image

Next on the agenda is grinding rivets ... lots of rivets. I've got the remove the spring buckets, radius arm cross member and the stock pivot brackets, all of which are held in by Fords beloved rivets.

User avatar
Lurch
Peak Putters Member
Peak Putters Member
Posts: 2363
Joined: Thu Nov 08, 2007 7:10 am
Location: Pasco

Re: Bunny v2.0

Postby Lurch » Thu Aug 18, 2016 9:23 am

I wouldn't stress the truss too much. That thing will never see the abuse the race truck did.
You can follow me.... but it's gonna hurt ;)

User avatar
TJDave
Peak Putters VP
Peak Putters VP
Posts: 2806
Joined: Sat Jan 12, 2008 11:47 am
Location: East Richland

Re: Bunny v2.0

Postby TJDave » Thu Aug 18, 2016 10:52 am

I seem to recall a pic in the old banner rotation....
The original bunny in flight. :shock:
2018 JLU Rubicon
Tow bar mount
Trailer hitch

User avatar
Don
Posts: 816
Joined: Wed Mar 14, 2007 4:40 pm
Location: Pasco, WA

Re: Bunny v2.0

Postby Don » Thu Aug 18, 2016 12:33 pm


User avatar
SPR
Peak Putters Member
Peak Putters Member
Posts: 2343
Joined: Thu Mar 15, 2007 6:31 am
Location: Tri-Cities

Re: Bunny v2.0

Postby SPR » Thu Aug 18, 2016 8:13 pm

How much do you think the rig will weight when done?
I don't Text (at least not very well), I eat Blackberrys, and I only Twitter after sex...

Wrench
Peak Putters Member
Peak Putters Member
Posts: 1237
Joined: Sat May 30, 2009 7:23 am
Location: in a van down by the river

Re: Bunny v2.0

Postby Wrench » Thu Aug 18, 2016 8:42 pm

Air chisels work great for those rivets.
Paul
'84 XJ, '19JL

User avatar
Don
Posts: 816
Joined: Wed Mar 14, 2007 4:40 pm
Location: Pasco, WA

Re: Bunny v2.0

Postby Don » Fri Aug 19, 2016 5:10 am

SPR wrote:How much do you think the rig will weight when done?


I'm finding the specs for stock weight as 3800lbs. I figure I'll add 150 in suspension and 300 in cage and accessories.

Also, the wheelbase is 102".

Interesting comparison, the Jeep LJ`s are 3800lbs and 103".

The explorer weight bias is going to be a little different. Obviously the TTB front end is going to put a different twist on things.

User avatar
Don
Posts: 816
Joined: Wed Mar 14, 2007 4:40 pm
Location: Pasco, WA

Re: Bunny v2.0

Postby Don » Fri Aug 19, 2016 5:17 am

Wrench wrote:Air chisels work great for those rivets.


I'm planning on taking the approach of skinny wheeling the head off then air hammering the nub out. I've got about 20 to do.

With what I got done last night, the rivets and a couple frozen brake fittings are all that's left of the tear down.

User avatar
Don
Posts: 816
Joined: Wed Mar 14, 2007 4:40 pm
Location: Pasco, WA

Re: Bunny v2.0

Postby Don » Fri Aug 19, 2016 7:57 pm

KIMG1215-640x360.jpg
KIMG1215-640x360.jpg (85.36 KiB) Viewed 11015 times


Don:+20, Dreaded Rivets:0. Rivet removal went smooth using the grind and air hammer method. Only took about an hour.

Tear down is now officially complete! I want to start putting it together so bad, but I've got cleaning, painting, reinforcing and a locker to do.

User avatar
Don
Posts: 816
Joined: Wed Mar 14, 2007 4:40 pm
Location: Pasco, WA

Re: Bunny v2.0

Postby Don » Tue Aug 30, 2016 7:02 am

Progress has been a little slow on the Bunny over the last couple of weeks because now I'm taking care of all the tedious stuff that will hopefully pay off in the end. I'm cleaning and painting everything i touch, installing the front locker, installing the rear axle truss and diff cover, reinforcing the front diff, doing ball joints, replacing wheel bearings, replacing axle seals, completely replacing all of the brakes.

Here are a few pictures:

Barnes4wd 8.8 axle truss. It's simple, smallish and should help. This will be complimented by a 3/8" thick fabricated steel diff cover.
Image

Image

Image

Image

Knuckles and spring plates sand blasted and painted. All ready for new ball joints and adjustable eccentrics
Image

Front Aussie locker installed. The front end will be getting a c-clip eliminator, skid plate and reinforcement plates.
Image

User avatar
Don
Posts: 816
Joined: Wed Mar 14, 2007 4:40 pm
Location: Pasco, WA

Re: Bunny v2.0

Postby Don » Thu Sep 01, 2016 9:36 am

Got some iron in the mail yesterday!

Image


As soon as I mock up the suspension I'm going to make a decision on bump stops. These are what I'm thinking:
http://www.kartek.com/parts/progressive ... 2bbfd4696e

Air bumps would be cool, but I think maybe unnecessary. I also don't want to worry about checking the nitro charge, seals, etc.

Any thoughts on the kartek bumps?

OldGreen
Posts: 4502
Joined: Tue Mar 13, 2007 6:21 am
Location: coming or going?

Re: Bunny v2.0

Postby OldGreen » Fri Sep 02, 2016 3:10 pm

No issue as long as the shocks are doing a good job.


Return to “Projects and Build-Ups”

Who is online

Users browsing this forum: No registered users and 2 guests