Downsizing from a JKUR to a '97 TJ
Re: Downsizing from a JKUR to a '97 TJ
250# down, 250# more to go...
- Attachments
-
- 24D153D4-EA17-48C1-90FE-1AFC7E958F1F.jpeg (1.41 MiB) Viewed 13420 times
Re: Downsizing from a JKUR to a '97 TJ
And the other half is off. Haha! Jose, you thought this Jeep was high off the ground? You should see it less 500#’s!
- Attachments
-
- 0213307E-4A67-45D0-8996-0ADBF46EEEB9.jpeg (1.43 MiB) Viewed 13408 times
-
- 03B7C4F8-6294-44E4-B17E-7CA12562A44F.jpeg (1.44 MiB) Viewed 13408 times
Re: Downsizing from a JKUR to a '97 TJ
I know it’s probably no big deal for most of you but it’s exciting to me bacause I’ve never taken apart a vehicle like this before.
Re: Downsizing from a JKUR to a '97 TJ
Anyone know what these are? Do I need to remove them from the old fenders and reinstall them on the new ones? They weren’t connected to anything?
- Attachments
-
- 66C1D1DA-1BC9-414F-BA5D-B52E92D9BD74.jpeg (835.55 KiB) Viewed 13408 times
-
- 8BC4B8D3-AEA1-421B-9746-B8A2AC08C077.jpeg (1009.08 KiB) Viewed 13408 times
Re: Downsizing from a JKUR to a '97 TJ
Those are for when you disconnect the sway bar, the open end of the link rotates up and slips onto that stub.
Yep, I've wheeled one of those, too...
Re: Downsizing from a JKUR to a '97 TJ
Oh haha, no sway bar on this thing! Guess I don’t need em.
Re: Downsizing from a JKUR to a '97 TJ
Have those on my Jeep. They are part of a rubicon express swaybar disconnect system. There should be a hole at the end where a cotter pin would be used to keep the disconnected swaybar link stowed. Yeah you can ditch those as you stated.
2004 TJ Wrangler X (Rubiclone)
2.5" OME Lift, 1.25 in Body Lift, Flat Fender Flares
35x12.50x15 Maxxis Razor MTs
D30 ARB 4.56s Rear JKD44 w/ 8.8 disk brakes Ford 9" goodies, 4.56 and ARB.
2.5" OME Lift, 1.25 in Body Lift, Flat Fender Flares
35x12.50x15 Maxxis Razor MTs
D30 ARB 4.56s Rear JKD44 w/ 8.8 disk brakes Ford 9" goodies, 4.56 and ARB.
Re: Downsizing from a JKUR to a '97 TJ
Tool box
- Attachments
-
- 89066825-2722-4181-ADF9-4834E4FC6435.jpeg (1.18 MiB) Viewed 13353 times
-
- EA7FEE86-9B21-4496-8091-821EC5720CD0.jpeg (1.22 MiB) Viewed 13353 times
-
- 9A90FE8B-EFB0-44B7-B466-DA5E044875BD.jpeg (1.34 MiB) Viewed 13353 times
Re: Downsizing from a JKUR to a '97 TJ
Looks great. If you are still planning to mount your spare on top, my stock carrier is 7" deep. Should account for the wheel offset and width of tire.
I did some garage cleaning and found it on a shelf. Yours if you want it.
I did some garage cleaning and found it on a shelf. Yours if you want it.
2018 JLU Rubicon
Tow bar mount
Trailer hitch
Tow bar mount
Trailer hitch
Re: Downsizing from a JKUR to a '97 TJ
TJDave wrote:Looks great. If you are still planning to mount your spare on top, my stock carrier is 7" deep. Should account for the wheel offset and width of tire.
I did some garage cleaning and found it on a shelf. Yours if you want it.
Yes please
Re: Downsizing from a JKUR to a '97 TJ
what are the dimensions on the box?
Lightly Lifted and Locked LJ
I'm Scumby Dammit, take it or leave it!
I'm Scumby Dammit, take it or leave it!
Re: Downsizing from a JKUR to a '97 TJ
scumby wrote:what are the dimensions on the box?
35" W x 13" H x 30" L
4.2 Cubic ft of Storage
Re: Downsizing from a JKUR to a '97 TJ
Yrjan wrote:
35" W x 13" H x 30" L
4.2 Cubic ft of Storage
Sooooo... what are the other 3.7 cubic feets doing in there?
Yep, I've wheeled one of those, too...
Re: Downsizing from a JKUR to a '97 TJ
tobyw wrote:Yrjan wrote:
35" W x 13" H x 30" L
4.2 Cubic ft of Storage
Sooooo... what are the other 3.7 cubic feets doing in there?
Outside dimensions and storage I suppose... the drawer is obviously smaller than the outside dimensions...
measurements taken from the manufacturers web site.
Re: Downsizing from a JKUR to a '97 TJ
Made some progress this weekend. Thanks for coming by and helping me out Jose and Jerry.
- Attachments
-
- DCD4B642-F461-4448-876E-FAB466EC7394.jpeg (1.39 MiB) Viewed 13272 times
-
- 19F7E38E-8D7E-48CE-AABB-27A397FBAE5C.jpeg (1.63 MiB) Viewed 13272 times
-
- B18AF823-F862-4DAE-A986-A49CE60A6796.jpeg (1.4 MiB) Viewed 13272 times
-
- 5854567B-7A6C-4F70-9CDB-B0D8776EEB1D.jpeg (1.37 MiB) Viewed 13272 times
Re: Downsizing from a JKUR to a '97 TJ
More parts! Yay!
- Attachments
-
- E138C4D5-8AA8-4449-87AC-FC180AF1BCE7.jpeg (1.56 MiB) Viewed 13192 times
-
- 8284C883-88CA-4C37-AE0A-7A61ACCCE0E5.jpeg (959.7 KiB) Viewed 13192 times
Re: Downsizing from a JKUR to a '97 TJ
Dash mounted CB, yes sir!
- Attachments
-
- 92FB5166-4F40-406A-B64A-28FFB56E6C1A.jpeg (1.5 MiB) Viewed 13189 times
Re: Downsizing from a JKUR to a '97 TJ
Got one side done completely. Working on the other side then it’s off to Trevor’s for long arm upgrade.
- Attachments
-
- 3E92410E-5A26-451E-8319-47510484E4E5.jpeg (1.09 MiB) Viewed 13160 times
Re: Downsizing from a JKUR to a '97 TJ
Made some progress on mine this past weekend. Thanks for all the help Trevor. I seriously couldn’t have done it without you.
- Attachments
-
- 66A68E6E-BA45-4F87-858D-4DB4F00E5877.jpeg (1.82 MiB) Viewed 13092 times
-
- 15DC7650-8DF7-489E-AD53-1EC0F64F6672.jpeg (1.21 MiB) Viewed 13092 times
-
- 1714A6A2-F466-4FF8-844F-6216A02ADB3F.jpeg (1.31 MiB) Viewed 13092 times
-
- 4AEC963C-25D5-4883-B6EE-7E195798542D.jpeg (1.45 MiB) Viewed 13092 times
-
- 123C97A8-4497-4033-9E31-BB6111B685FD.jpeg (1.19 MiB) Viewed 13092 times
-
- 8C035B96-C891-4BA4-80C4-E050CE7279B9.jpeg (1.63 MiB) Viewed 13092 times
-
- 03DEC443-5CB8-486B-92AA-1C05F480D15C.jpeg (1.34 MiB) Viewed 13092 times
-
- 38BF3F88-9ABB-46F0-8EF9-F09361691D8E.jpeg (1008.65 KiB) Viewed 13092 times
-
- C2EB2C98-9799-4CF8-A020-18F31169B715.jpeg (1.01 MiB) Viewed 13092 times
-
- 2E21902A-E313-4879-AAFF-4FF0D0426835.jpeg (911.66 KiB) Viewed 13092 times
Re: Downsizing from a JKUR to a '97 TJ
Yrjan wrote:Tool box
Great idea and design for the tool box. We'll be working on buddy's TJ right after we finished installing the new rack and hard tonneau cover on the truck project. He's thinking of a smaller version of tool box at the back.
Re: Downsizing from a JKUR to a '97 TJ
dutton wrote:Yrjan wrote:Tool box
Great idea and design for the tool box. We'll be working on buddy's TJ right after we finished installing the new rack and hard tonneau cover on the truck project. He's thinking of a smaller version of tool box at the back.
why would you post a hyperlink in your response? do you work for 4wheelonline.com?
Re: Downsizing from a JKUR to a '97 TJ
Well that was fun! Thanks for getting some good pics! I took one of you mocking up the very first part before I started welding.
Re: Downsizing from a JKUR to a '97 TJ
Just got my hands on these beauties...
- Attachments
-
- 43D1A939-578D-434C-B0F4-1B1333CB8114.jpeg (1.01 MiB) Viewed 8909 times
Re: Downsizing from a JKUR to a '97 TJ
What’s the old stuff
Lightly Lifted and Locked LJ
I'm Scumby Dammit, take it or leave it!
I'm Scumby Dammit, take it or leave it!
Return to “Projects and Build-Ups”
Who is online
Users browsing this forum: No registered users and 1 guest